一、動力系統安裝

1、 Power system installation

發動機安裝：如果使用汽油發動機或甲醇發動機，首先要根據發動機的型號和尺寸，在模型的機身或機翼上設計并制作合適的發動機安裝座。安裝座要具有足夠的強度，能夠承受發動機在運轉過程中產生的振動和推力。將發動機固定在安裝座上，使用螺栓螺母擰緊，確保發動機安裝牢固，無松動現象。連接發動機的燃油系統，包括油箱、油管和化油器等部件。油箱要安裝在合適的位置，保證燃油能夠順利供應到發動機，同時要注意油箱的密封性，防止燃油泄漏。油管的連接要緊密，避免出現彎折或堵塞的情況。對于化油器，要根據發動機的使用說明進行調試，確保燃油與空氣的混合比例合適，發動機能夠正常啟動和運行。

Engine installation: If a gasoline engine or methanol engine is used, the first step is to design and manufacture a suitable engine mounting seat on the fuselage or wing of the model based on the engine model and size. The mounting bracket should have sufficient strength to withstand the vibration and thrust generated by the engine during operation. Fix the engine onto the mounting bracket and tighten it with bolts and nuts to ensure that the engine is securely installed without any looseness. Connect the fuel system of the engine, including components such as the fuel tank, fuel pipes, and carburetor. The fuel tank should be installed in a suitable position to ensure smooth fuel supply to the engine, while also paying attention to the sealing of the fuel tank to prevent fuel leakage. The connection of the oil pipe should be tight to avoid bending or blockage. For carburetors, it is necessary to debug them according to the engine's instructions to ensure that the mixture ratio of fuel and air is appropriate, and that the engine can start and run normally.

電動動力系統安裝：對于電動馬達動力系統，將電動馬達安裝在模型的相應位置，通常使用螺絲將馬達固定在特制的安裝支架上。連接馬達的驅動電路，包括電調（電子調速器）、電池等部件。電調是控制電動馬達轉速和轉向的關鍵設備，要根據馬達的功率和電池的電壓選擇合適的電調。將電調與馬達、電池和接收機正確連接，注意正負極的連接方向，避免接反導致設備損壞。在連接完成后，對電調進行初始化設置，根據實際需求調整馬達的轉速范圍、剎車功能等參數。

Installation of electric power system: For the electric motor power system, the electric motor is installed in the corresponding position of the model, usually using screws to fix the motor on a specially designed mounting bracket. Connect the drive circuit of the motor, including components such as electronic speed regulators and batteries. ESC is a key device for controlling the speed and steering of electric motors, and the appropriate ESC should be selected based on the power of the motor and the voltage of the battery. Connect the ESC to the motor, battery, and receiver correctly, paying attention to the connection direction of the positive and negative poles to avoid damage to the equipment caused by reverse connection. After the connection is completed, initialize the ESC and adjust the motor speed range, braking function, and other parameters according to actual needs.

二、控制系統安裝

2、 Installation of control system

舵機安裝：在模型的機翼、尾翼等需要控制舵面的部位安裝舵機。舵機的安裝位置要根據設計要求進行精確確定，確保舵機的輸出軸能夠準確帶動舵面運動。使用螺絲或膠水將舵機固定在安裝座上，安裝座可以是事先制作好的木質或塑料結構。連接舵機與舵面的連桿機構，連桿的長度和角度要根據模型的設計進行調整，保證舵機轉動時，舵面能夠按照預期的角度和方向運動。在連接連桿時，可以使用球形接頭等連接件，增加連接的靈活性，減少運動過程中的卡頓。

Installation of servos: Install servos on the wings, tail fins, and other parts of the model that require control of the rudder surface. The installation position of the servo motor should be accurately determined according to the design requirements to ensure that the output shaft of the servo motor can accurately drive the movement of the control surface. Use screws or glue to fix the servo on the mounting base, which can be a pre made wooden or plastic structure. The connecting rod mechanism between the servo and the control surface, the length and angle of the connecting rod should be adjusted according to the design of the model to ensure that the control surface can move according to the expected angle and direction when the servo rotates. When connecting the connecting rod, spherical joints and other connectors can be used to increase the flexibility of the connection and reduce the jamming during the motion.

接收機與飛行控制器安裝：將接收機安裝在模型內部合適的位置，要保證接收機能夠清晰地接收到遙控器發出的信號，避免受到其他電子設備的干擾?？梢允褂媚g貼或膠帶將接收機固定在模型框架上。如果模型配備了飛行控制器，同樣要選擇合適的安裝位置，確保飛行控制器能夠準確感知模型的姿態變化。飛行控制器通常需要水平安裝，并且要盡量靠近模型的重心位置。使用螺絲將飛行控制器固定在安裝板上，然后將安裝板固定在模型框架上。連接接收機、飛行控制器和各個舵機、電調等設備的信號線，確保信號傳輸正常。在連接過程中，要對照設備說明書，仔細檢查線路連接是否正確，避免出現插錯接口等問題

Installation of receiver and flight controller: Install the receiver in a suitable position inside the model, ensuring that the receiver can clearly receive signals from the remote control and avoid interference from other electronic devices. The receiver can be fixed to the model frame using Velcro or tape. If the model is equipped with a flight controller, it is also necessary to choose a suitable installation location to ensure that the flight controller can accurately perceive the attitude changes of the model. Flight controllers usually need to be installed horizontally and as close as possible to the center of gravity of the model. Fix the flight controller onto the mounting plate using screws, and then secure the mounting plate onto the model frame. Connect the signal lines between the receiver, flight controller, and various servos, electronic controllers, and other equipment to ensure normal signal transmission. During the connection process, it is necessary to refer to the equipment manual and carefully check whether the circuit connection is correct to avoid problems such as incorrect interface insertion

本文由大型航空模型制作友情奉獻.更多有關的知識請點擊:http://2012xyx.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message